Verwenden Sie zur Reinigung des Gerätes keine Flüssigkeiten auf Alkohol- oder Ammoniak-basis. Falls erforderlich, wischen Sie das Gerät mit einem leicht angefeuchtetem Tuch ab.
Trennen Sie vorher den Monitor von der Versorgungsspannung.
8 Notizen
Flat-Panel Display (12.1“)
for Industrial Use
Operating Instructions
1 General Information ... 5 1.1 Important Safety Precautions ... 5 1.2 Cleaning the Flat-Panel Display ... 6 2 Operation ... 7 2.1 Commissioning... 7 2.2 Controls and LEDs... 9 2.2.1 Power key ... 9 2.2.2 OSD keys ... 9 2.2.3 Intensity P1 ... 9 2.2.4 Hotkeys ... 9 2.2.5 LED ... 9 2.2.6 Coding switch S1 ... 10 2.2.7 Ground switch S2 ... 10 2.3 Power supply / power switch ... 10 2.4 OSD menu... 11 2.5 Settings of the coding switches ... 15 3 Specifications and Connections ... 17 3.1 Specifications ... 17 3.2 Connections... 18 3.2.1 PE Grounding terminal ... 18 3.2.2 X0 Line input ... 18 3.3 Mechanical Dimensions ... 22 4 Overview of the Video Cables ... 23 4.1 Video Cable for Video Module and Control Teletext Module, Monochrome... 23 4.2 Video Cable for Control Teletext Module C, Color... 24 4.3 Video Cable for Graphics Control Board ... 25 4.4 Video Cable for EPC 8 Module ... 26 5 Improvements ... 27 5.1 Changes for Lathe Controls with External Control Module ... 27 6 Errors... 29 6.1 Error Analysis... 29 7 Service and Maintenance ... 31 7.1 General Information... 31 7.2 Service... 31 7.3 Maintenance... 31 8 Notes ... 33
1 General Information
1.1 Important Safety Precautions
Read these instructions carefully and keep them for later reference.
Observe all warnings and instruction labels on the products.
Always disconnect the power plug before cleaning! Do not use liquid cleaning agents or cleaning sprays; use a damp cloth instead.
Before connecting the AC cable to the DC adapter make sure that the voltage corresponds to that of your local power supply system.
Under no circumstances insert any metal objects into the openings of the monitor!
Danger of electrical shock!
To avoid danger of electrical shock, the monitor must not be opened. Only qualified technicians are allowed to open the housing.
Never operate the monitor with a defective power cable.
Do not allow any object to rest on the power cable.
Be sure to hold the plug, not the cable, when disconnecting the display from an electric socket.
Openings in the display cabinet are provided for ventilation. To prevent overheating, these openings must not be blocked or covered.
Do not fit your display at any locations subject to high humidity and dust.
Do not expose the display to rain or use it near water. If the display accidentally gets wet, unplug it and contact an authorized dealer immediately.
If your display does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or service center.
High temperatures may cause problems. Do not use your display in direct sunlight, and keep it away from heaters, stoves, fireplaces, and other sources of heat.
Unplug the display when it is going to be left unused for an extended period of time.
Unplug your display from the electric outlet before any service.
Do not press on the flat-panel screen, since it is very sensitive.
Do not touch the flat-panel display with bare hands: Fingerprints are hard to remove and may damage the display.
The monitor must not be subjected to direct sunlight or other sources of heat. During operation the flat-panel display should not face a source of light to avoid glare.
To ensure proper heat dissipation place your monitor in a location with adequate ventilation.
Be careful when moving and transporting your monitor!
1.2 Cleaning the Flat-Panel Display
Cleaning the flat-panel display
Carefully wipe the screen with a soft and clean lens brush of camel hair or a soft, clean and lint-free cloth to remove dust and other particles without scratching the surface.
If it is still not clean, gently wipe the monitor with a damp rag.
Do not use ketones (e.g. acetone), ethyl alcohol, toluene, ethyl acid, methanol or chlorides for cleaning, since these substances may damage the surface.
Do not exert pressure on the front of your flat-panel display.
2 Operation
2.1 Commissioning
Ensure that your control is not under power.
Connect the grounding cable to the grounding connector of the monitor (JH products).
Connect the power cable to the monitor (monitor requires line voltage).
Connect the video cable of the control to the video signal connector of the monitor.
Switch on the control.
Note
If this cable is missing, you must insert a ground conductor from the central ground of the machine to the monitor.
Note
Make sure that the cable shield is connected to the connector housing on both cable ends.
Note
*** For connecting the flat-panel display to the video module a monochrome adapter cable (length 1 m), ID 510 195-01 must be connected to socket CN4.
The old video module 4022 226 3720 has to be replaced by the new version 4022 226 3721!
If the flat-panel display is connected to the control teletext module as a replacement of a monochrome VDU, the adapter cable is required as well. A color video cable can be inserted into the machine, if you want to switch from monochrome to colored mode with the control teletext modules 4022 226 3432 and 4022 226 3433.
See “Video Cable for Control Teletext Module C, Color” on page 24.
PE Ground
OSD Operating keys for OSD menu LED Status LED
Power ON/OFF switch
S1 Coding switch
S2 Ground switch
P1 Intensity For the controls TNC 246, LE 306,
351, 360, CNC 132, 232, 234 select maximum intensity.
X0 Line input
X1 Signal input 15-pin HD female (analog) BC 110; EPC (VME) X2 Signal input 9-pin female (TTL) BE 411; BE 412; BE 511 X3 25-pin female (TTL) monochrome BE 110; BE 211; BE 311
X4 15-pin female (TTL) BE 132; BE 212; BE 511; BE 512
X5 15-pin female (analog) EPC (VME)
X6 15-pin female (TTL) Video module and control text
(CNC 3000)
X7 25-pin connector (TTL) color GCB (CNC 5000)
2.2 Controls and LEDs
2.2.1 Power key
2.2.2 OSD keys
2.2.3 Intensity P1
2.2.4 Hotkeys
Switch device on and off
Normally there is no need to press this key as the device switches on automatically when the supply voltage is applied.
Key:
Description:
"Down"
Reduces the values in submenus Key:
Description:
"Up"
Increases the values in submenus Key:
Description:
"Select"
- Selects a function in the main menu - Selects a function in a submenu Key:
Description:
"Menu"
1st Keystroke: OSD main menu is displayed
2nd Keystroke: Activates a parameter in a submenu;
its value can then be changed.
Designation: "P1"
Type: Potentiometer
Function: Grayscale adjustment
Function:
Key:
Description:
Auto Adjust
"Down"
Automatic setting of optimum display quality Function:
Key:
Description:
Adjust brightness and contrast
"Select"
Fast setting of brightness and contrast independently of the OSD menu
Designation:
Status:
"Status"
Off Device is off; no supply voltage
2.2.6 Coding switch S1
2.2.7 Ground switch S2
2.3 Power supply / power switch
The unit switches on as soon as it is powered by a supply voltage between 100 and 250 Vac.
Designation: "S1"
Type: DIL switch
Function: 1 = Red
2 = Green 3 = Blue
4 = Inverse video 5 = Intensity 6 = Inverse sync
Designation: "S2"
Type: Toggle switch
Function: Switchover: Ground = PE
Ground to PE 100 kW 100 nF
2.4 OSD menu
The on-screen display (OSD) allows the end user to adjust various (image) parameters in a menu that is self-explanatory, user-friendly and easy to use. The factory default setting of the monitor ensures that all requested timings are displayed in the best possible quality. If it still becomes necessary to change some parameters, the OSD menu can be called by pressing the "Menu"
key. If no key is pressed for several seconds while the OSD menu is being displayed, the current values are stored and the OSD menu disappears.
To obtain the display below press the “Menu“ key.
The illustration shows the items of the Main menu on the left side and those of the "Picture"
submenu on the right side.
Each submenu item can be selected with the “Menu” key. Press the “Select“ key to select brightness, contrast, h position, v position, phase, clock etc. The selected parameters can be changed with the “-“or “+” key.
The illustration below shows the "Advanced" submenu.
To return to the main menu, press the “menu“ key once.
To select sharpness, gamma, color temp, the “Select“ key must be pressed. These parameters can then be set with the “-“or “+” key.
The illustration below shows the "Pip" submenu.
The illustration below shows the "Advanced pip" submenu.
The illustration below shows the "Options" submenu.
The illustration below shows the "Utilities" submenu.
The illustration below shows the "Picture" submenu.
The illustration below shows the "Image" submenu.
The illustration below shows the "Setup" submenu.
Note
Changes in the OSD menu are stored automatically when the menu is exited.
When the OSD menu is called again, these changes are replaced again by the factory default settings.
2.5 Settings of the coding switches
Panel output color (only for connectors X2, X3, X4)
Intensity (only for connector X7)
Input signal Connector DIP Switch S1 Switch S2
1 2 3 4 5 6
Philips CNC 3000 series
with video module X6 off off off off off off GND = PE
Philips CNC 3000 series
with control teletext module X6 off off off off off on GND = PE
Philips CNC 5000 series
with GCB (graphics control board) X7 off off off off off on GND = PE
Philips VME series with EPC-8 module X1 / X5 off off off off off on GND = PE
≠P
Color red green blue yellow magenta cyan white
DIP switch S1 pin 5 5: On = Intensity low 5: Off = Intensity high
Note
For connection of TNC 246, LE 306, LE 355, LE 351, LE 360, CNC 132, CNC 232, CNC 234, the "P1" potentiometer must be set to maximum intensity!
3 Specifications and Connections
3.1 Specifications
(Subject to change without notice!)
Display Panel:
Color TFT LCD 12.1“
246 mm x 184.5 mm (HxV) 800 x 600 pixels (HxV) 6 bits
0.3075 mm x 0.3075 mm (HxV) 200:1
300 cd/m2
Video signals Signals:
Horizontal frequency:
Power supply Range: 100 ... 240 Vac
Connections / controls TTL inputs:
Analog inputs:
Ground connection:
Line input:
OSD menu:
Stud bolt M4 Power connector
Weight Total: Approx. 2.5 kg
Ambient conditions Storage temperature:
Operating temp.:
- 20 ... + 60° C 0 ... + 50° C
3.2 Connections
3.2.1 PE Grounding terminal
3.2.2 X0 Line input
3.2.3 X1 Signal input
3.2.4 X2 Signal input
Designation: "PE"
Type: Stud bolt M4
Designation: X0 "Power"
Type: Power connector
Power supply: 100 ... 240 Vac
Designation: "X1"
Type: HD SUB 15-pin, female
Pin layout: 1 = Signal (red) 2 = Signal (green) 3 = Signal (blue)
Type: 9-pin, D-sub female
Pin layout: 1 = Video
2 = Vacant 3 = Vacant 4 = Vacant 5 = Grayscale 6 = H sync 7 = Vacant 8 = Vacant 9 = V sync
3.2.5 X3 Signal input
3.2.6 X4 Signal input
Designation: "X3"
Type: 25-pin female, 2-row
Pin layout: 1 = Vacant
2 = H sync 16 = Grayscale 17 = Grayscale 18 = Video
Type: 15-pin female, 2-row
Pin layout: 1 = Vacant
2 = Vacant 12 = Grayscale 13 = Video 14 = Vacant 15 = Vacant
3.2.7 X5 Signal input
3.2.8 X6 Signal input
Designation: "X5"
Type: 15-pin D-sub female, 2-row
Pin layout: 1 = Signal (red) 2 = Signal (green) 3 = Signal (blue)
Type: 15-pin D-sub female, 2-row
Pin layout: 1 = Vacant
2 = Blue
3.2.9 X7 Signal input
Designation: "X7"
Type: 25-pin D-sub male, 2-row
Pin layout: 1 = GND (blue)
3.3 Mechanical Dimensions
4 Overview of the Video Cables
4.1 Video Cable for Video Module and Control Teletext Module, Monochrome
Monochrome operation is possible with:
Video module 4022 226 3721
Contr. telet. modules 4022 226 3431, 4022 226 3432 and 4022 226 3433
For monochrome operation you require the 1 m adapter cable (ID 510 195-01) or you make your own cable as per the drawing below.
For your new cable please use a well-shielded 6-pin computer cable.
Cable type: 3 x 2 x 0.14 mm² Length: 25 m max.
"Free" pins must not be assigned!
For some control models the shield must additionally be connected to the grounding bar of the control; please refer to the commissioning instructions of your control!
The signal ground (Sig. GND) must not be connected to the shield!
Only use shielded connector housings!
Your cable should only be as long as necessary, with a little allowance for mounting and dismounting the monitor.
4.2 Video Cable for Control Teletext Module C, Color
Color operation is possible with:
Contr. telet. modules C 4022 226 3432 and 4022 226 3433
You can use the existing video cable of your machine. The monitor is compatible with the old pin layout.
For your new cable please use a well-shielded 10-pin computer cable.
Cable type:5 x 2 x 0.14 mm² Length: 25 m max.
The pins labeled "Free" must not be assigned!
For some control models the shield must additionally be connected to the grounding bar of the control; please refer to the commissioning instructions of your control!
The signal ground must not be connected to the shield!
Only use shielded connector housings!
Your cable should only be as long as necessary, with a little allowance for mounting and dismounting the monitor.
4.3 Video Cable for Graphics Control Board
You can use the existing video cable of your machine.
For your new cable please use a well-shielded 12-pin computer cable.
Cable type:6 x 2 x 0.14 mm² Length: 20 m max.
The signal ground must not be connected to the shield!
Only use shielded connector housings!
Your cable should only be as long as necessary, with a little allowance for mounting and dismounting the monitor.
Hinweis
For the new cable the graphics control board must be modified to version 2 or higher!
This can be seen from the lower side of the handle (30112).
4.4 Video Cable for EPC 8 Module
You can use the existing video cable of your machine.
For a new video cable please use a high-quality VGA cable.
Cable type: 3 x coax + 3 x 2 x 0.14 mm² Length: 20 m max.
The signal ground must not be connected to the shield!
Only use shielded connector housings!
Your cable should only be as long as necessary, with a little allowance for mounting and dismounting the monitor.
5 Improvements
5.1 Changes for Lathe Controls with External Control Module
Owing to the high signal band width of the flat-panel display, it cannot be operated in combination with an External Control Module. The reason is that the video lines are not separately shielded in the cable. The edges of the scanning signals for the keyboard act capacitively on the video lines (cross-talking).
Solution:
Cut the lines marked by ** in the 37-pin D-sub connector (on the Contr. Teletext side).
Run a separate video cable from the Video connector of the Contr. Telet. Module to the monitor.
Cable for monochrome applications: See “Video Cable for Video Module and Control Teletext Module, Monochrome” on page 23.
Cables for color applications: See “Video Cable for Control Teletext Module C, Color” on page 24.
6 Errors
6.1 Error Analysis
No display (LED not lit)
Ensure that the device is under power.
Press the power key to switch the device on.
No display (LED shines orange)
Ensure that the signal cable is connected.
Ensure that the signal source is switched on and free of error.
Display too bright or too dark (LED shines green)
Change the values for contrast or brightness in the OSD menu.
Image position is incorrect
Press the “Down” key for the auto-adjust function.
Change the values for horizontal or vertical image position in the OSD menu.
Vertical or horizontal image interferences
Press the “Down” key for the auto-adjust function.
Change the clock or phase setting in the OSD menu.
7 Service and Maintenance
7.1 General Information
The commissioning and maintenance of the device may only be performed by a service technician authorized by the manufacturer.
Only have an authorized service technician repair the device.
7.2 Service
Opening the device creates danger of electric shock as conducting parts are exposed.
Therefore, separate the device from the supply voltage before you open it.
The manufacturer's liability for safety-relevant assemblies exists only, if service, maintenance and modifications are executed exclusively by authorized specialists and if original spare parts are used.
7.3 Maintenance
For cleaning the unit, do not use alcohol or ammonia-based cleaning agents. If required, wipe the device with a damp cloth. For this purpose disconnect the monitor from the power supply.
8 Notes
PL APS
02-384 Warszawa, Poland www.heidenhain.pl
PT FARRESA ELECTRÓNICA, LDA.
4470 - 177 Maia, Portugal www.farresa.pt
RO HEIDENHAIN Reprezentant¸a˘ Romania Bras¸ov, 500407, Romania
www.heidenhain.ro
RS Serbia BG RU OOO HEIDENHAIN
115172 Moscow, Russia www.heidenhain.ru
SE HEIDENHAIN Scandinavia AB 12739 Skärholmen, Sweden www.heidenhain.se
SG HEIDENHAIN PACIFIC PTE LTD Singapore 408593
www.heidenhain.com.sg SK KOPRETINA TN s.r.o.
91101 Trencin, Slovakia www.kopretina.sk SL NAVO d.o.o.
2000 Maribor, Slovenia www.heidenhain.si
TH HEIDENHAIN (THAILAND) LTD Bangkok 10250, Thailand www.heidenhain.co.th
TR T&M Mühendislik San. ve Tic. LTD. S¸TI· . 34775 Y. Dudullu –
Ümraniye-Istanbul, Turkey www.heidenhain.com.tr TW HEIDENHAIN Co., Ltd.
Taichung 40768, Taiwan R.O.C.
www.heidenhain.com.tw
UA Gertner Service GmbH Büro Kiev 01133 Kiev, Ukraine
www.heidenhain.ua
US HEIDENHAIN CORPORATION Schaumburg, IL 60173-5337, USA www.heidenhain.com
VE Maquinaria Diekmann S.A.
Caracas, 1040-A, Venezuela E-mail: purchase@diekmann.com.ve VN AMS Co. Ltd
HCM City, Vietnam
E-mail: davidgoh@amsvn.com ZA MAFEMA SALES SERVICES C.C.
Midrand 1685, South Africa www.heidenhain.co.za ES FARRESA ELECTRONICA S.A.
08028 Barcelona, Spain www.farresa.es
FI HEIDENHAIN Scandinavia AB 01740 Vantaa, Finland www.heidenhain.fi FR HEIDENHAIN FRANCE sarl
92310 Sèvres, France www.heidenhain.fr
GB HEIDENHAIN (G.B.) Limited
Burgess Hill RH15 9RD, United Kingdom www.heidenhain.co.uk
GR MB Milionis Vassilis 17341 Athens, Greece www.heidenhain.gr HK HEIDENHAIN LTD
Kowloon, Hong Kong
E-mail: sales@heidenhain.com.hk
HR Croatia SL
HU HEIDENHAIN Kereskedelmi Képviselet 1239 Budapest, Hungary
www.heidenhain.hu ID PT Servitama Era Toolsindo
Jakarta 13930, Indonesia E-mail: ptset@group.gts.co.id IL NEUMO VARGUS MARKETING LTD.
Tel Aviv 61570, Israel
E-mail: neumo@neumo-vargus.co.il IN HEIDENHAIN Optics & Electronics
India Private Limited
Chetpet, Chennai 600 031, India www.heidenhain.in
IT HEIDENHAIN ITALIANA S.r.l.
20128 Milano, Italy www.heidenhain.it JP HEIDENHAIN K.K.
Tokyo 102-0083, Japan www.heidenhain.co.jp KR HEIDENHAIN Korea LTD.
Gasan-Dong, Seoul, Korea 153-782 www.heidenhain.co.kr
MX HEIDENHAIN CORPORATION MEXICO 20290 Aguascalientes, AGS., Mexico E-mail: info@heidenhain.com MY ISOSERVE SDN. BHD.
43200 Balakong, Selangor E-mail: sales@isoserve.com.my NL HEIDENHAIN NEDERLAND B.V.
6716 BM Ede, Netherlands www.heidenhain.nl
NO HEIDENHAIN Scandinavia AB 7300 Orkanger, Norway www.heidenhain.no
PH MACHINEBANKS' CORPORATION Quezon City, Philippines 1113 AR NAKASE SRL.
B1653AOX Villa Ballester, Argentina www.heidenhain.com.ar
AT HEIDENHAIN Techn. Büro Österreich 83301 Traunreut, Germany
www.heidenhain.de
AU FCR MOTION TECHNOLOGY PTY LTD 3026 Victoria, Australia
E-mail: sales@fcrmotion.com BE HEIDENHAIN NV/SA
1760 Roosdaal, Belgium www.heidenhain.be BG ESD Bulgaria Ltd.
Sofia 1172, Bulgaria www.esd.bg
BR DIADUR Indústria e Comércio Ltda.
04763-070 – São Paulo – SP, Brazil www.heidenhain.com.br BY GERTNER Service GmbH
220026 Minsk, Belarus www.heidenhain.by
CA HEIDENHAIN CORPORATION Mississauga, OntarioL5T2N2, Canada www.heidenhain.com
CH HEIDENHAIN (SCHWEIZ) AG 8603 Schwerzenbach, Switzerland www.heidenhain.ch
CN DR. JOHANNES HEIDENHAIN (CHINA) Co., Ltd.
Beijing 101312, China www.heidenhain.com.cn CZ HEIDENHAIN s.r.o.
102 00 Praha 10, Czech Republic www.heidenhain.cz
DK TP TEKNIK A/S
DE HEIDENHAIN Vertrieb Deutschland 83301 Traunreut, Deutschland
08669 31-3132
| 08669 32-3132 E-Mail: hd@heidenhain.de
HEIDENHAIN Technisches Büro Nord 12681 Berlin, Deutschland
030 54705-240
HEIDENHAIN Technisches Büro Mitte 07751 Jena, Deutschland
03641 4728-250
HEIDENHAIN Technisches Büro West 44379 Dortmund, Deutschland
0231 618083-0
HEIDENHAIN Technisches Büro Südwest 70771 Leinfelden-Echterdingen, Deutschland
0711 993395-0
HEIDENHAIN Technisches Büro Südost 83301 Traunreut, Deutschland
08669 31-1345
Vollständige und weitere Adressen siehe www.heidenhain.de For complete and further addresses see www.heidenhain.de
Zum Abheften hier falzen! / Fold here for filing!