Status· Codes
1. Press Reset at the affected terminal and use your local logon/logoff procedures to reestablish a noncryptographic session
2. Request service.
For Service Personnel Only: Perform an ALT 2 IML; see page 2-3.
1-154
3174 Status Codes422 01HG
Description: A Network Services request was received that is not supported.
SNA sense code = X ' 1003 ' .
See "SNA Sense Codes" on page 2-41.
Alert Sent= Temporary.
Possible Cause: N/A
User Action: If the failure continues, contact the system programmer.
For Service Personnel Only: No action is required.
422 02HG
Description: An incorrect or unsupported Network Services (NS) header was received.
SNA sense code = X' 1007'.
See "SNA Sense Codes" on page 2-41.
Alert Sent= Temporary.
Possible Cause: N/A
User Action: If the failure continues, contact the system programmer.
For Service Personnel Only: No action is required.
422 03HG
Description: The maximum number of REQMS/RTM requests have been queued in the controller.
SNA sense code= X'0815'.
See "SNA Sense Codes" on page 2-41.
Alert Sent= Temporary.
Possible Cause: N/A
User Action: At the attached terminal, press Reset and retry the operation.
For Service Personnel Only: No action is required.
422 04HG
Description: Incorrect REQMS type received. This is an application program error.
SNA sense code = X' OBOC'.
See "SNA Sense Codes" on page 2-41.
Alert Sent= Temporary.
Possible Cause: N/A
User Action: No action is required. If the failure continues, contact the system programmer.
For Service Personnel Only: No action is required.
422 05HG 8182 8384
Description: An NMVT (RTM) or CSCF request was received with incorrect parameters.
8182 = SNA sense code.
8384 =Extended sense code.
See "SNA Sense Codes" on page 2-41.
Alert Sent = Temporary.
Possible Cause: N/A
User Action: No action is required. If the failure continues, contact the system programmer.
For Service Personnel Only: No action is required.
Status Codes
Chapter 1. 3174 Status Codes
1-155
Status Codes
422 06HG 8182 8384 8586 8788
Description: A signal request was received with an incorrect extension value, or a LUSTAT request was received with an incorrect status value.
User Action: If the problem continues, contact the system programmer or source node support personnel. The session must be re-initiated.
For Service Personnel Only: No action is required.
422 07HG 8182
Description: Category not supported.
B1 = Byte 3 of the transmission header (origin address field).
User Action: If the problem continues, contact the system programmer or source node support personnel. The session may have to be re-initiated.
For Service Personnel Only: No action is required.
422 08HG 81 to 810
Description: The requested function is not supported.
B1
Alert Sent = Temporary.
Possible Cause: N/A
User Action: If the problem continues, contact the system programmer or source node support personnel. The session may have to be re-initiated.
For Service Personnel Only: No action is required.
422 09HG 81 to 810
Description: An incorrect FM header was received.
B1-B7 = Bytes 0 through 6 of the request unit (RU).
BS = The number of RU bytes logged that are valid.
B9B10 = Extended sense data.
SNA sense code = X' 1008' .
See "SNA Sense Codes" on page 2-41.
Alert Sent = Temporary.
Possible Cause: N/A
User Action: If the problem continues, contact the system programmer or source node support personnel. The session may have to be re-initiated.
For Service Personnel Only: No action is required.
1-156
3174 Status Codes422 10HG 8182 8384
Description: An incorrect NMVT request was received.
8182 = SNA sense code.
8384 = Extended sense code.
See "SNA Sense Codes" on page 2-41.
Alert Sent= Temporary.
Possible Cause: N/A User Action:
1. Retry the operation.
2. If the failure continues, contact the system programmer.
3. Request service.
For Service Personnel Only: Contact your next level of support.
422 11HG
Description: Exception Response not allowed (LU 6.2).
Alert Sent =Temporary.
Status Codes
Possible Cause: Program error at source node. RQE1, RQE2, or RQE3 is not allowed on a DEALLOCATE_A8END type FMH7. It must flow with RQD1.
User Action: If the problem continues, contact the system programmer or source node support personnel.
For Service Personnel Only: No action is required.
423 51HG
Description: Response Time Monitor (RTM) counter overflow.
Alert Sent= Temporary.
Possible Cause: N/A
User Action: No action is required. The host system should send the RTM request to reset the counter.
For Service Personnel Only: No action is required.
424 01 HG 8182
Description: Session route inoperable (LU 6.2).
8182 =Path Control ID.
Alert Sent = None.
Possible Cause: Link failure User Action: Reactivate the link.
For Service Personnel Only: No action is required.
430 01HG
Description: The local logical unit (LU) could not start the local transaction program because it is permanently disabled.
SNA sense code = X '084C 0000'.
See "SNA Sense Codes" on page 2-41.
Alert Sent = None.
Possible Cause: There is a 3174 hardware or microcode error.
User Action: Request service.
For Service Personnel 9nly: Contact your next level of support.
Chapter 1. 3174 Status Codes
1-157
Status Codes
430 03HG 8182 8384 8586 8788
Description: Local transaction program parameter error.
81-88 =Transaction Program Name.
Alert Sent = Temporary.
Possible Cause: There is a 3174 hardware or microcode error.
User Action: Request service.
For Service Personnel Only: Contact your next level of support.
430 04HG 81 to 816
Description: The SNA distribution services transaction program detected an error while sending data (OS.SEND) to NetView DM. SNA/DS Message Unit Type
LU6.2 Return Code
OS.SEND detailed Error code Reserved.
For Service Personnel Only: Contact your next level of support.
430 05HG 81 to 816
Description: The SNA distribution services transaction program detected an error while receiving data (OS.RECEIVE) from NetView DM.
SNA/DS SNA Registered Sense Code SNA/DS Message Unit Type
= LU6.2 Return Code
=OS.RECEIVE detailed Error code
=Reserved.
For a description of the SNA Registered Sense Codes, refer to the 3174 Central Site Customizing User's Guide.
Alert Sent = None.
2. If the failure continues, contact the system programmer.
3. Request service.
For Service Personnel Only: Contact your next level of support.
1-158
317 4 Status Codes430 14HG or 24HG
Description: Additional Product Engineering data for status code 430-04.
Alert Sent = None.
Possible Cause: N/ A
User Action: See status code 430 04HG.
For Service Personnel Only: No action is required.
430 15HG or 25HG
Description: Additional Product Engineering data for status code 430-05.
Alert Sent = None.
Possible Cause: N/A
User Action: See status code 430 05HG.
For Service Personnel Only: No action is required.
430 51HG 8182
Status Codes
Description: The local logical unit (LU) could not start the local transaction program because it is temporarily disabled.
B 182 = Extended sense data.
SNA sense code= X'084B 6031 '.
See "SNA Sense Codes" on page 2-41 . Alert Sent = None.
Possible Cause: N/A
User Action: Retry the operation. If the failure continues, contact the system programmer.
For Service Personnel Only: No action is required.
431 01HG 8182 8384
Description: Unrecognized sense code.
B1-B4 =Unrecognized sense code.
Alert Sent= Temporary.
Possible Cause: N/A
User Action: If the problem continues, contact the system programmer or source node support personnel. The session must be re-initiated.
For Service Personnel Only: No action is required.
433 01HG
Description: A bracket initiation stopped (BIS) request was received after the local logical unit had processed its waiting requests due to the receipt of a previous BIS request.
Alert Sent = None.
Possible Cause: N/A
User Action: If the problem continues, contact the system programmer or source node support personnel. The session must be re-initiated.
For Service Personnel Only: No action is required.
433 02HG 81 to 815 Description:
B1-B6 B7-B9 B10-B14 B15
Inbound request processing error.
Bytes 0 through 5 of the transmission header.
Bytes 0 through 2 of the request header.
Bytes 0 through 4 of the request unit (RU).
The number of RU bytes logged that are valid.
Alert Sent = None.
Possible Cause: 3174 Microcode error
Chapter 1. 3174 Status Codes
1-159
Status Codes
User Action: Request service.
For Service Personnel Only: Contact your next level of support.
433 03HG B1
to
815Inbound response processing error.
Bytes
o
through 5 of the transmission header.Bytes O through 2 of the response header.
Bytes 0 through 4 of the response unit (RU).
The number of RU bytes logged that are valid.
Alert Sent = None.
Possible Cause: 3174 Microcode error User Action: Request service.
For Service Personnel Only: Contact your next level of support.
433 04HG7rlb. B1 to 815
Outbound request processing error.
Bytes 0 through 5 of the transmission header.
Bytes O through 2 of the request header.
Bytes
o
through 4 of the request unit (RU).The number of RU bytes logged that are valid.
Alert Sent = None.
Possible Cause: 3174 Microcode error User Action: Request service.
For Service Personnel Only: Contact your next level of support.
433 OSHG B1 to 815
Outbound response processing error.
Bytes 0 through 5 of the transmis_sion header.
Bytes O through 2 of the response header.
Bytes O through 4 of the response unit (RU).
The number of RU bytes logged that are valid.
Alert Sent = None.
Possible Cause: 3174 Microcode error User Action: Request service.
For Service Personnel Only: Contact your next level of support.
434 01HG B1B2 B3B4 BS
Description: End user not authorized.
B1-B3 = Bytes O through 2 of the request/response header.
User Action: If the problem continues, contact the system programmer or source node support personnel. The session may have to be re-initiated.
For Service Personnel Only: No action is required.
1-160
3174 Status Codes435 02HG
Description: An unexpected pacing request was received.
Possible Cause: N/A
User Action: No action is required.
For Service Personnel Only: No action is required.
435 03HG 81
Description: An unexpected pacing response was received (LU 6.2).
81, if present = Secondary send window size.
Alert Sent = None.
Possible Cause: Program error at source node
Status Codes
User Action: If the problem continues, contact the system programmer or source node support personnel.
For Service Personnel Only: No action is required.
436 01HG 81 to 810
Description: A stray response was received.
(A response that has a sequence number different from the current bracket sequence number.) B182
8384 B5-B9 B10
Bytes 4 and 5 of the transmission header.
Bytes 0 and 1 of the response header.
- Bytes 0 through 4 of the response unit (RU).
The number of RU bytes logged that are valid.
Alert Sent = None.
Possible Cause: N/A
User Action: No action is required.
For Service Personnel Only: No action is required.
436 02HG
Description: A late signal request was received.
Alert Sent = None.
Possible Cause: N/A
User Action: No action is required.
For Service Personnel Only: No action is required.
436 03HG
Description: Uncorrelated Un8ind received (LU 6.2).
Alert Sent = None.
Possible Cause: Program error at source node
User Action: If the problem continues, contact the system programmer or source node support personnel.
For Service Personnel Only: No action is required.
436 04HG
Description: An UnBind request was received for an LU 6.2 session.
Alert Sent =Temporary.
Possible Cause: N/A
User Action: None. This is an informational message only.
For Service Personnel Only: No action is required.
Chapter 1. 3174 Status Codes