• Keine Ergebnisse gefunden

Plugging in the Printer

Im Dokument L Easter10 Ref. Guide Rev.C (Seite 30-37)

1. Make sure that the printer is turned off. It is off when the P power button protrudes slightly from the surface of the control panel.

2. Check the label on the back of the printer to make sure the voltage required by the printer matches that of the electrical outlet you will be plugging it into. Also, make sure that you have the correct power cable for your power source.

c

Caution: It is not possible to change the printer’s voltage. If the rated voltage and your outlet voltage do not match, contact your dealer for assistance. Do not plug in the power cord.

3. If the power cord is not attached to the printer, connect it to the AC inlet on the back of the printer.

4. Plug the power cord into a properly grounded electrical outlet.

e3b

2

Easter10 Ref. Guide

R

Rev.C

A5 size Chapter 2 1-07-98 DR, pass 3

Installing the Ink Cartridges

w

Warning: The ink cartridges are self-contained units. Under ordinary use, ink will not leak from a cartridge. If ink does get on your hands, wash them thoroughly with soap and water. If ink gets into your eyes, flush them immediately with water.

Install the included ink cartridges as follows:

c

Caution:Use the ink cartridges packed with your printer the first time you install ink cartridges, otherwise the printer may not charge ink properly.

Note:

Do not open the ink cartridge packages until just before you install them or the ink may dry up.

1. Lower the output tray at the front of the printer; then, holding the tab on the cover, open the printer cover.

e18-L

Easter10 Ref. Guide Rev.C

A5 size Chapter 2 1-07-98 DR, pass 3

2. Turn on the printer by pressing the P power button.

The print heads move slightly to the left, which is the black ink cartridge install position (color ink cartridge installation begins in step 7). The B and A ink out lights come on and the P power light flashes.

c

Caution:Do not move the print heads by hand. Otherwise you may damage the printer.

e6d-new01

2

Easter10 Ref. Guide

R

Rev.C

A5 size Chapter 2 1-07-98 DR, pass 3

3. Lift up the black ink cartridge clamp, which is marked with a H symbol.

4. Open the ink cartridge packages that came with your printer and remove the cardboard, if necessary. Remove only the yellow tape seals from each cartridge as shown below.

Note:

Use the ink cartridges packed with your printer the first time you install the ink cartridges, otherwise the printer may not charge ink properly.

c

Caution: q Remove the yellow tape seals from the cartridges before installing them; otherwise the cartridge may become unusable.

q Do not remove the white portion of the tape seal from the top of the cartridge; otherwise, the cartridge may become clogged.

!e8

black ink

cartridge color ink

cartridge

Do not remove Remove

e-38

L

Easter10 Ref. Guide Rev.C

A5 size Chapter 2 1-07-98 DR, pass 3

q Do not remove the tape seals from the bottom of the cartridges; otherwise, ink will leak.

5. Lower the black ink cartridge into the cartridge holder with the label face-up and the arrow mark pointing to the rear.

6. Press the clamp down until it locks in place.

c

Caution: Once you install the ink cartridges, do not open their clamps again until you replace the cartridges. Otherwise, the cartridges may become unusable.

e24-

25-2

Easter10 Ref. Guide

R

Rev.C

A5 size Chapter 2 1-07-98 DR, pass 3

7. Next, press the

X

cleaning button to install the color ink cartridge. The printer moves the print heads to the color ink cartridge installation position. The clamp, which is marked with the I symbol, will appear.

c

Caution:Do not move the print heads by hand. Press the

X

cleaning button to move them to the color ink cartridge installation position. Otherwise you may damage the printer.

8. Lift up the color ink cartridge clamp. Install the color ink cartridge as described in steps 5 and 6, substituting “color ink cartridge” for “black ink cartridge” where appropriate.

Then go to step 9 to complete the ink cartridge installation.

new02

e8-2

L

Easter10 Ref. Guide Rev.C

A5 size Chapter 2 1-07-98 DR, pass 3

9. Close the printer cover then press the

E

load/eject button.

The printer moves the print heads and begins charging the ink delivery system.

Note:

Even if you do not press the E load/eject button, the printer moves the print heads and begins the ink charging process about 60 seconds after you install the ink cartridges.

The ink charging process takes up to 4 minutes to complete, during which time the P power light flashes and the printer produces a variety of mechanical sounds. These are normal. When the ink delivery system has been charged, the print heads return to their home position.

c

Caution: Never turn off the printer while the P power light is flashing.

The life of a cartridge depends on the amount of text and black-and-white graphics you print (for a black cartridge) and the amount and the number of colors used in your documents (for a color cartridge).

Note:

When ink runs out, see “Replacing an Ink Cartridge” in Chapter 8.

e7-2a2

2

Easter10 Ref. Guide

R

Rev.C

A5 size Chapter 2 1-07-98 DR, pass 3

Now you are ready to connect the printer to your computer. To connect the printer to your PC, see the following section. To connect it to your Macintosh, see page 2-20.

Im Dokument L Easter10 Ref. Guide Rev.C (Seite 30-37)