HARD DISK FAILURE, CHANGE YOUR DISK TO 'SUPPORT 6MB LOAD MODULE

~.~---~-~---~~--~---Disk Functions (Restoring ~.~---~-~---~~--~---Disk)

Step

Step

7

Select option 3

=

RESTORE DISK FROM DISKETTES. The following screen is displayed:

RESTORE DISK FROM DISKETTE

- MOUNT PRIMARY DISKETTE, THEN PRESS SEND

===>

F1:END F6:QUIT

8

Insert the primary diskette and press SEND.

• If during the process some tracks are found to be in error, the screen shown on page 4-19 will be displayed. Refer to this page for more details.

• You may have also one of the following messages:

HARDWARE CONFIGURATION SUPPORTS UP TO 4MB NCP LOAD MODULE

(refer to page 4-19).

INCREASING IN DISK SIZE - PLEASE WAIT SEVERAL MINUTES (refer to page 4-20).

READ CHECKING IN PROGRESS - PLEASE WAIT SEVERAL MINUTES (refer to page 4-20).

FORMAT COMPLETED, NO DEFECTIVE TRACK, ALTERNATE ASSIGNMENT MAP EMPTY

(refer to page 4-19).

HARD DISK FAILURE, CHANGE YOUR DISK TO 'SUPPORT 6MB LOAD MODULE

(refer to page 4-20).

• The following screen in displayed.

4-14

3745 Communication Controller: Advanced Operations Guide

o

o

,tstIriH P+h",,"L'LU&r1 II' 1!)flb'I.II :!IMi/"IIItiJr IIJridIItiHI+,dfl"HilliHHNWh'lIMU)''fI!l! "ID"WWf"I •• ,wnl/IJIIIII'W'alIIWIlfW*" " , . , ... we·Wp WIllI * MP,w"'HH' I'!!MII'"N.''' 't""MId"""w'H . . ·"

o

o o

0

o

Step

Disk Functions (Restoring Dis,k)

---mm/dd/yy hh:mm FUNCTION ON SCREEN: DISK FUNCTIONS

RESTORE DISK FROM DISKETTES

HOUNTED PRIMARY DISKETTE IDENTIFICATION:

CREATED ON ⁼ mm/dd/yy /t·1t-ljDD/YY)

m

SAVE ID = yyyyyy

n

INTERNAL ID = 00:20:38 ~ EC LEVEL = xxxxxx

- PLEASE CONFIRM YOUR SELECTION (Y OR N) ==>

===>

F1: END F3:ALARt,l F6: QUIT

D

Is the saving date.

D

Is the save identification you entered when you saved the fixed disk onto the diskettes.

Ii

Is the internal save identification automatically created during the save.

9

Check that the displayed information matches the information you wrote on the diskette envelopes:

• If they match, enter Y and press SEND.

• If they do not match, enter N; then insert the correct primary diskette.

Step 10

Insert the secondary diskette, then the third, fourth and fifth diskettes. Press SEND after you have inserted each diskette.

• If all the diskettes match, go to the next step.

• If the secondary, third, fourth or fifth diskettes do not match the primary diskette, the following screen is displayed:

---mm/dd/yy hh:mm FUNCTION ON SCREEN: DISK FUNCTIONS

RESTORE DISK FROM DISKETTES

DISKETTES DO NOT BELONG TO THE SAME SET

CREATED SAVE ID INTERNAL ID EC LEVEL PRHIARY 00/00/00 xxxxxxxx xxxxxxxx A4720 SECONDARY 00/00/00 yyyyyyyy yyyyyyyy A4721

- PRESS SEND

===>

F1: END F3:ALARH F6:QUIT

When the five diskettes are correctly checked, the disk restoration starts.

Step 11

Remove the write protect tab (if any) from the primary diskette, insert the diskette, then press SEND.

Chapter 4. Disk Functions (DIF) and Microcode Changes

4-15

Disk Functions (Restoring Disk)

When the primary diskette is copied, repeat the procedure with the secondary, third, fourth and fifth diskettes.

When the restoration is completed, the following screen is displayed.

---mm/dd/yy hh:mm FUNCTION ON SCREEN: DISK FUNCTIONS

RESTORE DISK FROM DISKETTES DISK CORRECTLY RESTORED

SELECT ONE ~F THE NEXT ACTIONS:

- IF YOU HAVE DONE CONCURRENT DISK REPLACEI-IENT,

B

PERFORM MOSS IML FROM CONTROL PANEL WITH SERVICE 0 THEN FUNCTION 1.

- IN ALL OTHER CASES, pm,fER OFF THE 3745

III

THEN POWER ON WITH FUNCTION 1 AND SERVICE O.

===>

Fl:END F3:ALARM

Step 12

Remove the fifth diskette then, as shown on the previous screen, select one of the following actions:

• 11

When the disk restore function is performed by the service representative:

Do not power off the 3745 if you have replaced a disk during a concurrent maintenance.

Perform only MOSS IML from the control panel (function 1 and service 0).

· m

When the disk restore function is performed by the customer from a backup copy:

a. Power off the 3745.

POWER ON (Reset) ~

POWER OFF

b. Wait 10 seconds.

c. On the control panel, press Function repeatedly until 1 is displayed then press Validate.

d. Power on the 3745. MOSS IML starts.

When MOSS is IMLed:

FOE is displayed on the control panel.

The 3745 CA Interface Display screen is displayed on the MOSS console.

4-16

3745 Communication Controller: Advanced Operations Guide

o

o

, •• t1 tmt'.lIIu'I"K'Plwt·, [ ' N ' " U l l i n l I t H " 'h'jlJhlllLd'lI!IHUJl!!r !!!IO!)(h'IHN'NW'N1'+lM'iIl!!P i f

o

o

o

o

o

Disk Functions (Restoring Dis~)

Step 13

After restoring the disk, the default password is IBM3745. You can refer to Chapter 16, "Passwords (PSW)" on page 16-1 to update the password.

Step 14

After restoring the disk from diskette, the NCP is no longer accessible. You must reload NCP. The RLA procedure (remote loading activation) may be used if the restore disk is performed on a remote controller.

This ends the procedure "Restoring the Disk from Diskettes".

Chapter 4. Disk Functions (DIF) and Microcode Changes

4-17

Disk Functions (Restoring Disk)

Formatting a Diskette

o ^{[Q 0 ( I}

^{SEND) •}

^{0 ( I}

^SEND)

Follow the procedure on the screen carefully.

If the diskette formatting (initialization) ends without errors, the message:

DISKETTE INITIALIZATION SUCCESSFULLY COMPLETED is displayed.

If there are errors, the following message is displayed:

DISKETTE INITIALIZATION UNSUCCESSFULLY COMPLETED

with the number of tracks in error. When this message is displayed, you must press F1, then the error and its associated alarm will be recorded for further analysis.

---mm/dd/yy hh:mm FUNCTION ON SCREEN: DISK FUNCTIONS

DISKETTE INITIALIZATION

DISKETTE INITIALIZATION UNSUCCESSFULLY COt-IPLETED:

NUt·IBER OF TRACK(S) IN ERROR WHILE FORI·IATTING:

NUI-IBER OF TRACK(S) IN ERROR WHILE CHECKING : WARNING: DO NOT USE THIS DISKETTE TO SAVE YOUR DISK

===>

Fl:END F3:ALAR~1 F6:QUIT

m 1m

• Remove the diskette and make sure that it is not damaged.

• Insert the diskette and make sure that:

- It is correctly inserted.

- The drive latch is correctly closed.

• Repeat the formatting procedure. If the procedure is again unsuccessful, repeat the procedure with a new diskette.

Discard the diskette that did not format correctly.

- If the problem persists:

CO

4-18

3745 Communication Controller: Advanced Operations Guide

o

()

1"#I',,'1IM"'!!!!1 Nf'lt!

o

o

o

o

o

1\ ! '01 II ! [ I I I "".tiIf""f" it! If ".15'11"; . . . . 1 ' ... Y!',+,FW'""'!I' .,'" . . . ' •• '.,,'I',.WW ... 'M' At I t

Disk Functions (Restoring Dis,k)

Im Dokument Advanced Operations Guide (Seite 123-128)