MAY NOT PERFORM AT OPTIMUM. CONTINUE?
DECLINE ACCEPT
Non-genuine ink cartridge is installed.
Select DECLINE to replace the ink cartridge with a genuine Epson ink cartridge. Selecting ACCEPT may void EPSON’s warranty.
See “About ink cartridges” on page 68 See “Replacing ink cartridges” on page 69
INK CARTRIDGE ERROR PLEASE INSTALL THE CORRECT CARTRIDGE
An ink cartridge that cannot be used with this printer is installed.
Remove the ink cartridge, and install an ink cartridge that can be used with this printer.
See “About ink cartridges” on page 68 See “Replacing ink cartridges” on page 69 NOZZLE CLOG DETECTED
NOT ENOUGH INK CONTINUE CLEANING?
YES (RECOMMENDED) NO
There is not enough ink to perform cleaning.
By clicking YES, the message to replace the ink cartridge appears. Replace the ink cartridge with a new one to continue cleaning.
See “Replacing Ink Cartridges” on page 66 NOZZLE CLOG DETECTED
NOT ENOUGH EMPTY SPACE IN MAINT TANK
CONTINUE CLEANING?
YES (RECOMMENDED) NO
There is not enough space in the
maintenance tank to perform cleaning.
By clicking YES, the message to replace the maintenance tank appears. Replace the maintenance tank with a new one to continue cleaning.
See “Replacing the Maintenance Tank” on page 71
CLOGGED NOZZLES DETECTED CLEANING RECOMMENDED
Print head nozzles are clogged.
Perform head cleaning to remove any clogs. This message continues to be displayed until the clogged nozzles have been cleared, but it is removed when a check pattern is printed.
Printing is possible while the message is displayed.
See “Head cleaning” on page 78
Error messages Description What to do
TAKE-UP DISCONNECTED SET AUTO TAKE-UP REEL SYSTEM IN PRINTER AND RESTART THE PRINTER
Auto Take-up Reel Unit is not correctly installed in the printer.
Turn the printer off, and then install the Auto Take-up Reel Unit properly.
See “Using Auto Take-up Reel Unit (For Epson Stylus Pro 9890/9908 only)” on page 46 TAKE-UP DISCONNECTED
AUTO TAKE-UP REEL UNIT IS DISCONNECTED
DO YOU CONTINUE?
NO
Auto Take-up Reel Unit is not correctly installed in the printer.
Select NO, and turn the printer off, and then install the Auto Take-up Reel Unit properly. If you select YES, the paper is ejected without using the Auto Take-up Reel Unit.
Error messages Description What to do
TAKE-UP ERROR
IS ANYTHING OBSTRUCTING THE TAKE-UP REEL SENSOR SYSTEM?
LOAD PAPER AGAIN
The Auto Take-up Reel Unit does not wind the paper.
Make sure there is no obstruction in the sensor system. Press the button to release the paper presser, and then set the paper correctly in the Auto Take-up Reel Unit.
See “Using Auto Take-up Reel Unit (For Epson Stylus Pro 9890/9908 only)” on page 46 SProofer DISCONNECTED
CONNECT SpectroProofer TO THE PRINTER
AND RESTART THE PRINTER
The SpectroProofer is not connected to the printer properly.
Turn the printer off, and then connect the SpectroProofer to the printer properly.
See the SpectroProofer Mounter 24"/44"
Setup Guide ILS20EP DISCONNECTED
REFER TO THE MANUAL AND CONNECT ILS20EP TO SpectroProofer RESTART THE PRINTER
The color measurement device (ILS20EP) is not connected properly.
Turn the printer off, and then connect the color measurement device (ILS20EP) to the
SpectroProofer properly.
See the SpectroProofer Mounter 24"/44"
Setup Guide
Error messages Description What to do
SpectroProofer ERROR REFER TO THE MANUAL TO FIND OUT HOW TO SOLVE THE PROBLEM
NN
*NN is the error number.
Error No. 01
The SpectroProofer is not connected to the printer properly.
Turn the printer off, and then remove the SpectroProofer from the printer. Connect the SpectroProofer to the printer properly, and then turn on the printer.
See "Removing the Mounter" in the SpectroProofer Mounter 24"/44" User’s Guide
See the SpectroProofer Mounter 24"/44"
Setup Guide
If the same error occurs, contact your dealer.
Error No. 13
The paper presser does not function properly due to one of the between the paper presser and
backing.
❏ The media type is not supported.
❏ The product is used out of its operational environment.
❏ Turn off the printer, and then remove the SpectroProofer. If there are objects such as packing materials around the backing, remove them. Then, attach the backing properly, and then turn on the printer.
See the See the SpectroProofer Mounter 24"/44" User’s Guide
See the SpectroProofer Mounter 24"/44" Setup Guide
❏ Check the media type and system requirements.
See "Supported Media" and "System Requirements" in the SpectroProofer Mounter 24"/44" User’s Guide
If the same error occurs, contact your dealer.
Error No. 15
The Color Measurement Device carriage does not function properly due to one of the following factors:
❏ There is some foreign object in the moving range of the carriage.
❏ Turn off the printer, and then remove the SpectroProofer. If there are objects such as packing materials around the backing, remove it. Then, attach the backing properly and turn on the printer.
See the See the SpectroProofer Mounter 24"/44" User’s Guide
See the SpectroProofer Mounter 24"/44" Setup Guide
❏ Check the media type and system requirements.
See "Supported Media" and "System Requirements" in the SpectroProofer Mounter 24"/44" User’s Guide
If the same error occurs, contact your dealer.
Error messages Description What to do