ENABLE-4953-TABLET-GIN

DISABLE-4953-TABLET-GIN = Ee! char

1100 (Level 0): Unrecognized command (Option 130r 14 not installed).

IA SET-PICK-APERTURE = EelA int

IA 11 (Level 2): Invalid aperture-width (must range from 0 to 4095).

IC SET-GIN-CURSOR

=

EelC int int

1011 (Level 2): Invalid device-function code. (See the description of the ENABLE-GIN com-mand for a table of device-function codes.)

IC13 (Level 2): Graphic input has already been enabled for the specified device-function code.

IC20 (Level 2): Segment does not exist, or is currently being defined.

IC21 (Level 2): Invalid segment-number (must range from Oto 32767).

ID DISABLE-GIN

=

^{EelD int}

1011 (Level 2): Invalid device-function code.

IE ENABLE-GIN = EciE int int

1011 (Level 2): Invalid device-function code.

IEOO (Level 2): The cursor segment for the specified device-function code does not exist. (It has been deleted after the SET-GIN-CURSOR command which assigned it to that device-function code.)

IE03 (Level 2): Command is invalid at this time. (The segment being used as the cursor for the specified device-function code is a seg-ment which is currently being defined.) IE10 (Level 2): The specified GIN device is not installed

in the terminal.

IE13 (Level 2): The specified GIN device is already enabled.

IE21 (Level 2): Invalid number-of-GIN-events. (Must range from 0 to 65535.)

IF SET-GIN-STROKE-FILTERING = EelF int int int 1011 (Level 2): Invalid device-function code. (See the

table with the ENABLE-GIN command for valid device-function codes.)

IFOa (Level 0): Unrecognized command. (The tablet option is not installed.)

IF10 (Level 2): Stroke filtering is not valid for the speci-fied device-function code. (Only allowed for stroke function.)

IF21 (Level 2): Invalid distance-filter (range is 0 to 4095).

IF31 (Level 2): Invalid time-filter (range is 0 to 32767).

IG SET-GIN-GRIDDING = EelG int int int

1011 (Level 2): Invalid device-function code. (See the table with the ENABLE-GIN command for valid device-function codes.)

IG10 (Level 2): Gridding does not apply to the specified device-function code. (Gridding is not allowed for the stroke function.)

IG21 (Level 2): Invalid x-grid-spacing (4112, 4113, 4114, 4116: 0 to 4095; 4115: _2³¹ to 2³¹_1).

IG31 (Level 2): Invalid y-grid-spacing (4112, 4113, 4114, 4116: a to 4095; 4115: _2³¹ to 2³¹_1).

A-6 REV, JAN 1984 41158 OPERATORS

IH SET-TABlET-HEADER-CHARACTERS = EclH int IQ REPORT-TERMINAL-SETTINGS = EclQ char char IHOO (Level 0): Unrecognized command. (Tablet option is No errors are detected for this command.

not installed.)

IH11 (Level 2): Invalid character-set-selector. (Must be 0 IR SET-GIN-RUBBERBANDING = EciR int int or 1; in Setup mode, must be CONTROL

1011 (Level 2): Invalid device-function code. (See the or LETTERS.)

ENABLE-GIN command for a table of device-function codes.)

II SET-GIN-INKING = Eell int int

IR10 (Level 2): Rubberbanding does not apply to the 1011 (Level 2): Invalid device-function code. (See the specified device-function code.

(Rubber-description of the ENABLE-GIN com- banding is only allowed for the locator mand for a table of device-function function. It is not allowed for the pick and

codes.) stroke functions.)

1110 (Level 2): Inking does not apply to the specified IR21 (Level 2): Invalid rubberbanding mode (must be 0, device-function code. (Inking is not 1, or 2).

allowed for the pick function.)

1121 (Level 2): Invalid inking mode (must be 0, 1 or 2). IS SET-REPORT-SIG-CHARS = EelS int in! int 1011 (Level 2): Invalid report-type-code. (Must be a valid Il SET-REPORT-MAX-LiNE-lENGTH = Eell int device-function code, or from -1 to -3.) IL 11 (Level 2): Invalid max-line-length. (Must range from IS21 (Level 2): Invalid sig-char. (Must range from 0 to

Oto 65535.) 127).

IS31 (Level 2): Invalid term-sig-char. (Must range from 0

1M SET-REPORT-EOM-FREQUENCV = EclM int to 127.)

IM11 (Level 2): Invalid EOM-frequency setting (must be 0

or 1). IT SET-TABLET-STATUS-STRAP = EclT int

ITOO (Level 0): Unrecognized command. (The tablet

IN SET-TABLET-SIZE = EelN int option is not installed.)

INOO (Level 2): Unrecognized command. (Requires ver- IT11 (Level 2): Invalid strap-setting (must be 0 or 1).

sion 2 or later of Option 13 or 14

firm-ware.) IV SET-GIN-AREA = EelV int int ;(y xy

IN11 (Level 2): Invalid tablet-size-mode. (Must be 0, 1, 1011 (Level 2): Invalid device-function (see

ENABLE-or 2.) GIN).

IVOO (Level 0): Unrecognized command; terminal

firm-IP REPORT-GIN-POINT = EciP int ware is Version 3 or earlier.

1011 (Level 2): Invalid device-function code. (See the IV03 (Level 3): Out of memory while processing

com-description of the ENABLE-GIN com- mand.

mand for a list of valid device-function _IV21 (Level 2): Invalid window-speciJier(range is -1 to

codes.) 64).

IE10 (Level 2): The specified GIN device is not installed IV31 (Level 2): Invalidfirst-corner (X or Y out of range 0

in the terminal. to 4095).

IE13 (Level 2): A plotter device is not assigned to the IV41 (Level 2): Invalid second-corner (X or Y out of range

specified port.

o

to 4095, or area is of zero width or

IP13 (Level 2): The device-function code names a device height).

which has already been enabled for a different graphic input function.

4115B OPERATORS REV, JAN 1984 ,A.-7

ERROR CODES

IW SET-GIN-WINDOW = EclW xy xy

IWOO (Level 0): Unrecognized command; terminal firm-ware is Version 3 or earlier.

IW11 (Level 2): I nvalid first-corner (X or Y out of range _2³¹ to 2³¹_1).

IW21 (Level 2): Invalid second-corner (X or Y out of range _2³¹ to 2³¹_1).

IX SET-GIN-DISPLAY-START-POINT = EclX int xy 1011 (Level 2): Invalid device-function parameter. (See

ENABLE-GIN for a table of valid device-function codes.)

IXOO (Level 0): Invalid command; firmware is Version 3 or earlier.

IX21 (Level 2): Invalid start-point (4112, 4113, 4114, 4116: X = Ot04095, Y = Oto 4095;

4115: X = _2³¹ to 2³¹_1, Y = _2³¹ to 2³¹_1).

JO and J1: Disk System Errors on Power-Up

J002 (Level 3): Memory error detected by standard firm-ware.

J 1 02 (Level 3): Memory error detected by optional peripheral firmware.

J109 (Level 3): Hardware initialization error in option controller board.

J8 ACTIVATE-LPOS = EcJ8

JBOO (Level 0): Unrecognized command (Option 42/43/45 or Version 6 or higher not installed).

JB03 (Level 2): A filename was specified when LPOS was resident in terminal memory, or a filename was not specified, but LPOS was active.

JB10 (Level 2): The boot-file was not found.

JB11 (Level 2): Illegal filename.

JB12 (Level 3): Out of memory while performing com-mand.

JB13 (Level 2): Context error (local programmability already active).

JB19 (Level 2): Disk hardware error (drive not ready, 1/0 error).

(Level 2): Data format error (Options 3A and 9 only).

(Level 3): Out of memory while attempting DMA transfer (Option 3A only).

(Level 2): Attempt to copy an entire disk volume onto itself (e.g., a copy from FO: to FO:).

(Level 2): Specified source device is not installed, or file does not exist.

(Level 2): Invalid source specifier.

(Level 3): Out of memory while parsing the parame-ter, or while executing the command.

(Level 2): Parameter 1 context error (not an input device, or device is busy).

(Level 2): Disk hardware error or drive not ready on the source device, or error in DMA block transfer.

(Level 2): Separator parameter missing.

(Level 2): Invalid separator (must be empty string or TO; in Setup mode, must be TO).

(Level 3): Out of memory while parsing the parameter.

".-"--(Level 2): Specified destination device is not installed.

(Level 2): Invalid destination specifier.

(Level 3): Out of memory while parsing the parame-ter, or while executing the command.

(Level 2): Parameter 3 context error. (Invalid desti-nation device, device is busy or full, or existing disk file is write protected.) (Level 2): Disk hardware error or drive not ready on

the destination device, or error in DMA block transfer.

41158 OPERATORS

JD DIRECTORY

=

EcJD device string device JDOO (Level 2): Unrecognized command. (Disk drive

option is not installed.)

JD10 (Level 2): The specified source device is not installed or file does not exist.

JD11 (Level 2): Invalid source specifier.

JD12 (Level 3): Out of memory while parsing the parame-ter, or while executing the command.

JD13 (Level 2): Context error in parameter 1. (The speci-fied device is not a disk drive, or failed reading bit map.)

JD19 (Level 2): Disk hardware error (or drive not ready) for the disk drive whose directory is being requested.

JD20 (Level 2): Separator parameter missing.

JD21 (Level 2): Invalid separator (must be empty string or TO).

JD22 (Level 3): Out of memory while parsing the parame-ter.

JD30 (Level 2): The specified destination device is not installed.

JD31 (Level 2): Invalid destination specifier.

JD32 (Level 3): Out of memory while parsing the parame-ter, or while executing the command.

JD33 (Level 2): Parameter 3 context error. (The device specified is not a valid destination device, the disk is full, or the file is

write-protected.)

JD39 (Level 2): Hardware error for the destination device.

(110 error, write-protect error, disk drive not ready, or DMA block transfer error.)

JE STOP-SPOOLING = EcJE

No errors are detected for this command.

JF FORMAT-VOLUME

=

EcJF device

JFOO (Level 2): Unrecognized command. (Disk drive option not installed.)

JF10 (Level 2): Device is not installed.

JF11 (Level 2): Invalid device specifier.

JF12 (Level 3): Out of memory while parsing the parame-ter.

JF13 (Level 2): The device specified is not a disk drive, is write-protected, is busy, detects a verify error, detects a bit map error, or is not mounted.

JF19 (Level 2): Hardware error at the specified disk drive.

(Format error, drive not ready, or write-protect switch or notch error.)

JH SET-DMA-BLOCK-SIZE

=

EcJH int

JHOO (Level 0): Unrecognized command (Option 3A is not installed.)

JH03 (Level 2): Command received after DMA failed to power up.

JH11 (Level 2): Invalid parameter (must be from 1 to 65504).

JJ DISMOUNT

=

EcJJ device

JJOO (Level 0): Unrecognized command; firmware is Version 3 or earlier, or there are no disk options installed.

JJ10 (Level 2): The device is not installed.

JJ11 (Level 2): Invalid device parameter.

JJ13 (Level 2): Parameter 1 context error (not a valid device, or device is busy).

41158 OPERATORS REV, JAN 1984 A-9

ERROR CODES

"

JK DELETE-FILE

=

EcJK device JQ REPORT-DEVICE-STATUS

=

EcJQ device

JKOO (Level 2): Unrecognized command. (Disk drive JQ10 (Level 2): Device is not installed.

option is not installed.)

JQ11 (Level 2): Invalid device specifier.

JK10 (Level 2): The specified file does not exist or device

JQ12 (Level 3): Out of memory while parsing parameter.

is not installed.

JK11 (Level 2): I nvalid file-specifier.

JR RENAME-FILE

=

EcJR device string device JK12 (Level 3): Out of memory while parsing parameter.

JROO (Level 2): Unrecognized command. (Disk drive JK13 (Level 2): The specified device is not a disk drive, is option is not installed.)

write-protected, is busy, or detects a bit

JR10 (Level 2): The specified device or file does not exist.

map error.

JK19 (Level 2): Disk hardware error. (1/0 error, drive not JR11 (Level 2): Invalid old-filename specifier.

ready, or hardware write-protect error.) JR12 (Level 3): Out of memory while parsing parameter.

JR13 (Level 2): Parameter 1 context error (file is

write-JL LOAD

=

EcJL device protected, device is busy, or command

JL02 (Level 3): Out of memory while performing LOAD detects invalid disk format).

command. JR19 (Level 2): Disk hardware error. (110 error, drive not JL03 (Level 2): Nesting error. (LOAD commands are ready, or hardware write-protect error.)

nested too deeply.) JR20 (Level 2): Separator parameter is missing.

JL10 (Level 2): File or device does not exist. JR21 (Level 2): Invalid separator (must be empty string or

JL 11 (Level 2): Invalid source specifier. TO).

7

JL12 (Level 3): Out of memory while parsing parameter, JR22 (Level 3): Out of memory while parsing parameter.

or while executing the command. JR30 (Level 2): Either the device specified in parameter 3 JL13 (Level 2): Context error in parameter 1. (Not a valid does not exist, or is different from the

device specified in parameter 1 , or new-source device, device is busy, or

com-filename already exists.

mand detects a disk format error.)

JL19 (Level 2): Device hardware error (disk hardware JR31 (Level 2): Invalid new-filename specifier.

error, drive not ready, or DMA block trans- JR32 (Level 3): Out of memory while parsing parameter.

fer error).

JR33 (Level 2): P~rameter 3 context error (invalid device specifier).

JP PROTECT-FILE

=

EcJp device int

(Level 2): Disk hardware error. (110 error, drive not JR39

JPOO (Level 2): Unrecognized command. (Disk drive ready, or hardware write-protect error.) option is not·installed.)

JP10 (Level 2): The specified file or disk drive does not exist.

JP11 (Level 2): Invalid file specifier.

JP12 (Level 3): Out of memory while parsing parameter.

JP13 (Level 2): Either the specified device is not a disk drive, or the file (or entire diskette volume) has been write-protected.

JP19 (Level 2): Disk hardware error. (110 error, drive not ready, or hardware write-protect error.) JP21 (Level 2): Invalid write-protect-mode (must be

o

^{or 1).}

A-10 REV, JAN 1984 41158 OPERATORS

JS SPOOL = EcJS device string device JU SET-USER-NUMBER = EcJU int

JS01 (Level 2): Data format error (Options 3A and 9 only). JUOO (Level 0): Unrecognized command (firmware is JS02 (Level 3): Out of memory while attempting DMA Version 3 or earlier or disk option is not

transfer (Option 3A only). installed).

JS03 (Level 2): Command context error. (A spooling JU11 (Level 2): Invalid user-number (must be 0 to 15).

operation is already in progress.)

JS10 (Level 2): Specified source does not exist. JV SAVE = EcJV string int string device

JS11 (Level 2): Invalid source specifier. JV02 (Level 3): Out of memory while attempting DMA transfer (Option 3A only).

JS12 (Level 3): Out of memory while parsing parameter,

JV01 (Level 2): RAS and RUN are valid for raster termi-or while executing the command.

nals only.

JS13 (Level 2): Parameter 1 context error. (Not a valid

JV11 (Level 2): Invalid thing-to-be-saved. (Must be MAC, source device, or device is busy.)

SEG, RAS, or RUN. The latter two codes JS19 (Level 2): Device hardware error (disk hardware are valid for 4112, 4113, and 4115

termi-error, drive not ready, or DMA block trans- nals only.) fer error).

JV12 (Level 3): Out of memory while parsing parameter, JS20 (Level 2): Separator parameter is missing. or while executing the command.

JS21 (Level 2): Invalid separator (must be empty string or JV20 (Level 2): The specified macro or segment does not

TO). exist, or segment is being defined.

JS22 (Level 3): Out of memory while parsing parameter. JV21 (Level 2): Invalid item-number-or-count.

JS30 (Level 2): Specified destination does not exist. JV31 (Level 2): Invalid separator (must be empty string or JS31 (Level 1): Invalid destination device specifier. TO).

JS32 (Level 3): Out of memory while parsing parameter, JV32 (Level 3): Out of memory while parsing the

or while executing the command. parameter.

JS33 (Level 2): Parameter 3 context error. (Not a valid JV40 (Level 2): The specified destination is not installed.

destination, device is busy, or existing file JV41 (Level 2): Invalid destination specifier.

is write protected or open.)

JV42 (Level 2): Out of memory while parsing the parame-JS39 (Level 2): Device hardware error (disk hardware ter, or while executing the command.

error, drive not ready, or DMA block

trans-JV43 (Level 2): Not a valid destination device, device is fer error).

busy, or existing disk file is write protected or open.

JV49 (Level 2): Device hardware error. (110 error, drive not ready, hardware write-protect error, or DMA block transfer error.)

41158 OPERATORS REV, JAN 1984

A-l1

KO: Keyboard System Errors

K002 (Level 3): Out of memory while initializing the key-board system.

KA ENABLE-DIALOG-AREA = EcKA int

KA 11 (Level 2): Invalid enable-mode (must be 0 or 1).

KC CANCEL = EcKC

No errors are detected for this command.

KD DEFINE-MACRO = EcKD int int-array

KD11 (Level 2): Invalid macro number (must be in range -32768 to -32742, -32740 to -32737, -32608 to -32513, or -1 to 32767).

KD21 (Level 2): Invalid int-array (length must be from 0 to 65535, int values must be from 0 to 127).

KD22 (Level 3): Insufficient memory to define macro.

KE SET-ECHO

=

^{EcKE int}

KE11 (Level 2): Invalid echo-mode (must be 0 or 1).

KF LFCR

=

EcKF int

KF11 (Level 2): Invalid LFCR-mode (must be 0 or 1).

KH HARDCOPY = EcKH int

KH01 (Level 2): Copier fault condition; operator assist-ance required (Option 9 only).

KH11 (Level 2): Invalid hard-copy-code (must be 0, 1, or 2).

KI IGNORE-DELETES = EcKI int

KI11 (Level 2): Invalid ignore-deletes mode (must be

o

or 1).

KL LOCK-KEYBOARD = EcKL int

KL 11 (Level 2): Invalid keyboard-lock-mode (must be

o

or 1).

KM SET-MARGINS = EcKM int

KMOO (Level 0): Unrecognized command. (The terminal is not a 41140r 4116.)

KM 11 (Level 2): Invalid number-oj-margins (must be from 1 to 8).

KN RENEW-VIEW

=

EcKN int

KN02 (Level 3): Out of memory while attempting to renew a view. (This error can also occur as a result of pressing the PAGE key.)(4112, 4113, and 4115 only.)

KN10 (Level 2): The view specified does not exist.

KN11 (Level 2): Parameter out of range (must range from -32768 to 32767).

KP SET-PAGE-FULL-ACTION

=

EcKP int

KP11 (Level 2): Invalid page-Jull-action. (Must range from

o

to 7.)

KQ REPORT-ERRORS

=

EcKQ No errors are detected for this command.

KR CRLF

=

^{EcKR int}

KR11 (Level 2): Invalid CRLF-mode (must be 0 or 1).

KS SET-SNOOPY-MODE

=

EcKS int

KS11 (Level 2): Invalid snoopy-mode (must be 0 or 1) KT SET-ERROR-THRESHOLD = EcKT int

KT11 (Level 2): Invalid error-threshold-level (must be from

o

^{to 4).}

KV RESET = EcKV

No errors are detected for this command.

A-12 REV, JAN 1984 41158 OPERATORS

KX EXPAND-MACRO = EeKX int

KX11 (Level 2): Invalid macro-number (must be from -32768 to -32742, -32740 to -32737, -32608 to -32513, or 0 to 32767).

KY SET-KEY-EXECUTE-CHAR = EeKY int

KY11 (Level 2): Invalid key-execute-char (must range from

o

to 127).

KZ SET-EDIT-CHARS = EeKZ int int int

KZ11 (Level 2): Invalid char-delete character (must range from 0 to 127).

KZ21 (Level 2): Invalid line-delete character (must range from 0 to 127).

KZ31 (Level 2): Invalid take-literally character (must range from 0 to 127).

LB SET-DIAlOG-AREA-BUFFER-SIZE = EeLB int LB11 (Level 2): Invalid number-oj-lines. (Must range from

2 to 32767.)

lC SET-DIALOG-AREA-CHARS

=

EeLC int

LC11 (Level 2): Invalid number-oj-chars. (4112,4113: 5 to 80; 4114, 4116: 5 to 819; 4115: 5 to 160.)

lE END-PANEL

=

^EcLE

LEOO (Level 0): Unrecognized command. (The terminal is not a 4112,4113, or4115).

LE03 (Level 1): No panel is currently being defined.

LE02 (Level 3): Out of memory while performing END-PANEL command.

IF MOVE = EeLF xy

LF11 (Level 2): Invalid position (4112,4113,4114,4116:

X = Ot04095,Y = Ot04095;4115:X =

LH 11 (Level 2): Invalid position (4112,4113,4114, 4116:

X = Ot04095,Y = Ot04095;4115:X =

o

to 4095 or _2³¹ to 2³¹_1, Y

=

^{0 to 4095}

or _2³¹ to 2³¹_1.)

LI SET-DIAlOG-AREA-INDEX = EeLi int int int L100 (Level 0): Unrecognized command. (The terminal is

not a 4112,4113, or 4115.)

L111 (Level 2): Invalid character-index. (Range is 0 to 32767.)

L121 (Level 2): Invalid character-background-index.

(Range is 0 to 32767.)

L131 (Level 2): Invalid wipe-index. (Range is 0 to 32767.) lJ SET-DIALOG-AREA-AL TERNATE-INDEX

=

EeLJ int LJOO (Level 0): Unrecognized command (terminal is not

Version 4 or later; only valid for 4112, 4113,or4115).

LJ 11 (Level 2): Invalid index (range is 0 to 65535).

lK INCLUDE-COPY-OF-SEGMENT

=

EeLK int LK02 (Level 3): Out of memory while performing

INCLUDE-COPY-OF-SEGMENT. (4112, 4113 and 4115 only).

LK10 LK11 LK13

(Level 2): Segment does not exist.

(Level 2): Invalid segment-number (must be -3, -1, or from 1 to 32767.)

(Level 2): The segment specified is currently being defined.

lL SET-DIALOG-AREA-UNES = EcLl int

LL 11 (Level 2): Invalid number-oj-lines. (4112, 4113: 2 to 34; 4114, 4116: 2 to 520; 4115: 2to 64.) lM SET-DIALOG-AREA-WRITING-MODE

=

^{EclM int}

LM11 (Level 2): Invalid writing-mode (must be 0 or 1).

41158 OPERATORS REV, JAN 1984 A-13

ERROR CODES

LP BEGIN-PANEL-BOUNDARY = EeLP xy int LZ CLEAR-DIALOG-SCROLL = EeLZ LPOO (LeveIO): Unrecognized command. (Terminal is not No errors are detected for this command.

a 4112, 4113, or a 4115.)

LP02 (LeveI3): Out of memory while defining panel. MA SET-GRAPHTEXT-SLANT = EeMA real LP03 (LeveI2): Alphatext is not allowed within apanel- MAOO (LeveIO): Unrecognized command; firmware is

definition. When this error is detected, Version 3 or earlier.

the panel being defined is closed, as if an

MA11 (LeveI2): Invalid slant-angle (must range from END-PANEL command had been

received. -32767.0 to 32767.0).

LP11 (LeveI2): I nvalid first-point (4112, 4113: X = 0 to

MB SET-BACKGROUND-INDICES = EeMB int int 4095, Y = 0 to 4095; 4115: X = 0 to 4095

or _2³¹ to 2³¹_1, Y = 0 to 4095 or _2³¹ to MBOO (LeveIO): Unrecognized command. (The terminal is

2³¹_1). not a 4112, 4113, or 4115}.

LP21 (LeveI2): Invalid draw-boundary-mode (must be 0 MB11 (LeveI2): Invalid text-back ground-index (must

or 1). range from -2 to 32767}.

MB21 (LeveI2): Invalid dash-gap-index (must range from

LS SET-DIALOG-AREA-SURFACE = EeLS int -2 to 32767).

LSOO (Level 0): Unrecognized command. (The terminal is

nota4112, 4113, or4115.) MC SET-GRAPHTEXT-SIZE = EeMC int int int

LS11 (Level 2): Invalid surface-number. (4112: 1 to 3; MC11 (Level 2): Invalid value in parameter 1 . (4112, 4113, 4113: 1 to 4; 4115: 1 to 8.) 4114,4116: 1 to 4095; 4115: 1 to 2³¹_1.)

/

MC21 (Level 2): Invalid value in parameter 2. (4112, 4113,

LT GRAPHIC-TEXT = EeL T string 4114, 4116: 1 to 4095; 4115: 1 to 2³¹_1.)

LT03 (Level 2): Command is invalid at this time MC31 (Level 2): Invalid value in parameter 3. (4112, 4113, (graphtext is not allowed within a panel- 4114,4116: 0 to 4095; 4115: 0 to 2³¹_1.) definition).

LT11 (Level 2): Invalid array count (must be from 0 to MD BEGIN-FILL-PATTERN = EeMD int int int int 65535).

MDOO (Level 0): Unrecognized command. (The terminal is LT12 (Level 2): Out of memory while parsing the not a 4112,4113, or 4115.)

parameter.

MD02 (Level 3): Not enough memory available for fill pattern.

LV SET-DIALOG-AREA-VISIBILITY = EeLV int

MD03 (Level 2): Another fill pattern is currently being LV03 (Level 0): One or more of the dialog area parame- defined.

ters was altered when the dialog area was

MD11 (Level 2): Invalidfill-pattern-number (must range made visible.

from 1 to 32767).

LV11 (Level 2): Invalid visibility-mode. (Must be 0 or 1.)

MD21 (Level 2): Invalid pattern-width (4112, 4113: 1 to 32;

4115: 1 to 1280).

LX SET-DIALOG-AREA-POSITION = EeLX xy

Invalid pattern-height (4112, 4113: 0 to MD31 (Level 2):

LX11 (Level 2): Invalid position (4115: X or Y out of range 480; 4115: 0 to 1024).

Ot04095).

MD41 (Level 2): Invalid bits-per-pixel (on the 4112, must be 1, 2, 3, or 6; onthe4113, must be 1, 2, 3,4, or 6; on the 4115, must be 1 to 8).

A-14

REV, JAN 1984 41158 OPERATORS

ME END-FILL-PATTERN

=

EcME

MEOO (Level 2): Unrecognized command. (Terminal is not a 4112,4113, or 4115).

MF SET-GRAPHTEXT-FONT = EcMF int MF10 (Level 2): Font is not defined.

MF11 (Level 2): Invalidjonl-number (must range from

a

to 32767).

MG SET-GRAPHICS-AREA-WRiTING-MODE = EcMG in1 MGOO (Level 0): Unrecognized command. (Terminal is not

a 4112, 4113, or4115.)

MG11 (Level 2): Invalid writing-mode. (Must be

a

or 1.) MI SET-PICK-ID

=

EcMI int

MI03 (Level 2): Command is invalid at this time. (No seg-ment is currently being defined.) MI11 (Level 2): Invalid pick-number. (Must range from

a

MM11 (Level 2): Invalid marker-number (must be from

a

to 10).

MP SELECT-FILL-PATTERN

=

EcMP int

MPOO (Level 2): Unrecognized command. (The terminal is not a4112, 4113, or4115.)

MP10 (Level 2): Specified jill-pattern has not been defined.

MP11 (Level 2): Invalid jill-pattern (must range from -32768 to 32767.)

MQ SET-GRAPHTEXT-PRECISION = EcMQ int MQ11 (Level 2): Invalid precision mode (must be 1 or 2).

MR SET-GRAPHTEXT-ROTATION

=

EcMR real MR11 (Level 2): Invalid angle-in-degrees (must range from

-32767.0 to 32767.0).

MS SET-PANEL-FILLING-MODE

=

EcMS int int int MSOO (Level 0): Unrecognized command. (Terminal is not

a 4112,4113, or 4115.)

MS11 (Level 2): Invalid overstrike/replace mode (must be

a

or 1).

MS21 (Level 2): Invalid cover-houndary mode (must be 0 or 1).

MS31 (Level 2): Invalid pattern-keying-mode (must be from

a

to 3).

MWOO (Level 0): Unrecognized command. (The terminal is not a4114 or4116.)

MW11 (Level 2): Invalid width. (Must be 0 or 1.) MY SELECT-ALPHATEXT-SIZE-GROUP

=

EcMY int MYOO (Level 0): Unrecognized command (terminal is not a

4114 or 4116).

MY11 (Level 2): Invalid group (must be either 0 or 1).

MZ SET-ALPHATEXT-SIZE

=

EcMZ int int int

MZOO (Level 0): Unrecognized command. (Terminal is not a41140r4116.)

MZ11 (Level 2): Invalid size-multiplier (must range from 1 to 16).

MZ21 (Level 2): Invalid inter-character-spacing (must range from

a

to 15).

MZ31 (Level 2): Invalid interline-spacing (must range from

o

^{to 255).}

4115B OPERATORS REV, JAN 1984 A-15

ERROR CODES

NB SET-STOP-BITS = EcNB int

NB11 (Level 2): Invalid number-oJ-stop-bits (must be 1 or 2).

ND11 (Level 2): Invalid transmit-delay. (Must range from 0 to 65535.)

NE SET-EOF-STRING = EcNE int-array

NE11 (Level 2): Invalid EOF-string (must contain from

o

to 10 characters, with each character represented by an int in the range from Ot0127).

NE12 (Level 3): Out of memory while parsing the parameter.

NF SET-FLAGGING-MODE

=

EcNF int

NF SET-FLAGGING-MODE

=

EcNF int

Im Dokument COMPUTER DISPLAY TERMINAL 4115B/M4115B (Seite 173-196)