• Keine Ergebnisse gefunden

Quick Clean of the Milk Tank System

The quick clean of the milk tank system should be carried out after every use so that no milk residues can remain in the system and dry on or go mouldy.

1. Fill the milk tank (6) with water (see the “Handling and Operation” chapter – “Filling the Milk Tank”).

2. Fold out the milk nozzle (4) using the lever (5) (Picture G).

3. Press the button (21) to switch on the device and preheat the water. The control pan-el (15) fl ashes during the heating process.

4. Place a suitable cup below the milk nozzle.

5. As soon as the device has heated up, the control panel stops fl ashing. Press the but-ton (19). A beep sounds, the self-cleaning starts and the button fl ashes.

6. Run the programme and pour away the contents of the cup after the self-cleaning fi nishes.

7. Repeat this process if necessary.

Intensive Clean of the Portafi lter and Milk Tank System

During the intensive clean, the portafi lter is also thoroughly rinsed through in addition to the milk tank system. This allows coffee residues which are stuck on to be rinsed out of the portafi lter and the sieves if applicable.

1. Fill the water tank (16) with water (see the “Handling and Operation” chapter – “Filling the Water Tank”).

2. Also fi ll the milk tank (6) with water (see the “Handling and Operation” chapter – “Filling the Milk Tank”).

3. Insert the portafi lter (10) into the device (see the “Handling and Operation” chapter – “Insert-ing / Remov“Insert-ing the Portafi lter”).

4. Fold out the milk nozzle (4) using the lever (5) (Picture G).

5. Press the button (21) to switch on the device and preheat the water. The control pan-el (15) fl ashes during the heating process.

6. Place a suitable cup below the coffee outlet (11) and the milk nozzle.

7. As soon as the device has heated up, the control panel stops fl ashing. Press the  but-ton (19) for approx. 5 seconds. A beep sounds, the self-cleaning starts and the button fl ashes.

8. If you want to stop the cleaning, press the button again. The device switches to stand-by mode.

9. Pour away the water in the cup.

10. Repeat this process if necessary.

07440_Inlay_DE-EN-FR-ES-IT_A5_V1.indb 33

07440_Inlay_DE-EN-FR-ES-IT_A5_V1.indb 33 21.06.2021 10:50:2821.06.2021 10:50:28

Descaling

Limescale deposits have an adverse effect not only on the quality of the espresso and the water, but they also cause power losses and shorten the lifespan of the device. The thicker a limescale layer is, the more diffi cult it is to remove.

We therefore recommend regularly removing limescale deposits with a descaling agent in accordance with the water quality in your area and how often the device is used (approx. every 2 – 6 weeks).

The fi rst indications that descaling is required are a large amount of steam being produced and slower brewing of the espresso.

The device indicates that it needs to be descaled at regular intervals! When the yellow control lamp (22) is lit, a descaling process needs to be carried out. The control lamp goes out as soon as a cleaning or descaling process has been carried out. This process may require more than one water tankful. In this case, a measuring cup may need to be used to add more water to the water tank (16) during the process until the yellow control lamp goes out.

For descaling we recommend the BEEM Premium Descaler Concentrate. The effi cient, food-safe and environmentally friendly BEEM Premium Descaler Concentrate is available from selected spe-cialist stockists, via our website www.beem.de or from our customer service department on request.

Descaling with the BEEM Premium Descaler Concentrate

For careful descaling of the device, carry out the intensive clean with a concentrate/water solution of no more than 1:20 (one part concentrate to 20 parts water) (see the “Self-Cleaning” section – “Intensive Clean of the Portafi lter and Milk Tank System”).

• Then allow the descaling solution to take effect for a little while.

• Repeat the process a second and third time if necessary.

• Remove the rest of the solution from the water tank (16) and milk tank (6).

• Fill both tanks with clear water. To rinse the device, run the same programme with clear water at least two times. The device is now descaled and ready to be used again.

Storage

Disconnect the device from the mains power when it is not going to be used for a prolonged period. Clean the device again if necessary (see the “Cleaning and Care” chapter) and let it dry completely.

Store the device and all accessories in a dry, clean, frost-free place that is protected from direct sunlight and cannot be accessed by children or animals.

07440_Inlay_DE-EN-FR-ES-IT_A5_V1.indb 34

07440_Inlay_DE-EN-FR-ES-IT_A5_V1.indb 34 21.06.2021 10:50:2921.06.2021 10:50:29

Troubleshooting

If the device does not work properly, check whether you are able to rectify the problem yourself.

If the problem cannot be solved with the steps that are listed, contact our customer service department.

Do not attempt to repair a defective electrical device yourself!

Problem Possible cause Fix

The control panel (15) does not light up / the device cannot be switched on.

The mains plug is not inserted

correctly in the plug socket. Correct the fi t of the mains plug.

The plug socket is defective. Try another plug socket.

There is no mains voltage. Check the fuse of the mains connection.

The fuse in the fuse box is triggered.

Too many devices connected to the same circuit.

Reduce the number of devices in the circuit.

Water runs out of the device.

There is too much water in the

water tank (16). Do not overfi ll the water tank!

The water tank (16) is not placed

in its mount correctly. Correct the fi t of the water tank.

A function has been selected, but the device beeps constantly and the red control lamp (20) fl ashes. The control panel (15) does not light up.

There is no water in the water tank (16).

Detach the water tank from the device and fi ll it with water.

Place a cup beneath the coffee outlet (11).

Press any button. Some water will run through the water system into the cup. The red control lamp will go out, the device will stop beeping and can be restarted.

The red control lamp (20) is lit up permanently.

The device is defective. Contact the customer service department.

The yellow control

lamp (22) fl ashes. The device is furred up. Descale the device.

The espresso runs very slowly into the cup.

The coffee outlet (11) or the

sieve (8, 9) is clogged. Clean the portafi lter (10) and the sieve.

The device is furred up. Descale the device.

07440_Inlay_DE-EN-FR-ES-IT_A5_V1.indb 35

07440_Inlay_DE-EN-FR-ES-IT_A5_V1.indb 35 21.06.2021 10:50:3021.06.2021 10:50:30

Problem Possible cause Fix

The espresso is too weak.

There is not enough coffee

powder in the sieve (8, 9). Pour the right quantity of coffee powder into the respective sieve.

The set espresso quantity is too much for the quantity of coffee powder in the sieve.

Programme the perfect amount of espresso to suit your own taste in the device.

A large amount of steam is produced in the brewing process.

The device is furred up. Descale the device.

Cappuccino, latte macchiato or milk froth has been selected, but there is no milk in the milk tank (6).

Wait until the programme has run through. Allow the device to cool down a little. Remove the milk tank from the device and fi ll it.

Select the programme you want again.

During use, an unpleasant smell is detected.

The device is being used for the fi rst time.

A smell often develops when new devices are fi rst used. The smell should disappear once the device has been used several times.

The device has previously been descaled.

Rinse out the device with fresh water.