• Keine Ergebnisse gefunden

If If ~

N/A
N/A
Protected

Academic year: 2022

Aktie "If If ~"

Copied!
3
0
0

Wird geladen.... (Jetzt Volltext ansehen)

Volltext

(1)

Dear seQ TCP/IP Customer,

This letter contains installation instr'llctions for the SCQ~ TCP/IP:J Runtime Maintenance Supplement (for seQ ~ System V Release 3.2v2.0). When installed in conjunction with seQ TCP/IP 1.1.3, this maintenance supplement increases the number ofavaiIable UDP endpoints from 32 to 128. corrects a minor telnet problem, reconfigures tunable kernel parameters spet..ific to TCP/IP, and establishes a directory needed for token ring configuration. This supplement contains the following files:

J tmplinit.Ulcpms Jtmplpermslutcpms Jtmplpermslprep.utcpms Jusrlliblcusromlurcpms.rmv JusrllibltcprtlIDI udpl Space.c Jusrlliblutcprtlidtune JUSTI bin/telnet

During installation, the maintenance supplement backs up the files that it replaces.

l~ Before You Instnll the ~fnintenance Supplement

Make sure that you have configured your system as described below before you start installing the TCP/IP Maintenance Supplement.

1.1 Required Software

This maintenance supplement is intended ~or SCQ TCP/IP 1.1.3 running on one of the following operating systems:

~~0 Ui~1X 3ySL~ui V{38G Rol~ J.2';2.0 Cflcppy dkitrituticn)

• SCQ UNIX System V/386 Release 3.2v2.0 (tape distribution)

• SCQ UNIX System V/386 Release 3.2v2.0 (Micro Channel dislribution)

If you try to install the maintenance supplement without TCP/IP, you see the following message and the installation terminates:

SCQ TCP/IP Runtime System must be installed.

The system software environment does not match the intended environment.

Please contact your Support Department for help.

Installation terminating.

If you have a release ofTCPIIP other than 1.1.3 installed. you see the follOwing message:

Expected SCQ TCP/IP Runtime System =elease 1.1.3f.

The system software environment does noe maech the intended environmene.

Do you wish eo continue?

If you answer n, the installation tern1inates.

!fyou answer y, the installation continues; however. other relenses ofTCP/IP are not supponed at this time.

sec

and the

sec

1010 ars regisu:n:d trademarks

of

The Sill" Cruz Openr.ion. file. ia die USA and omer c:auncries. TCP/IP is a register=! trademaric of Interactive SYstemS Corporation. m..1X is a registered tradcmuk of UNIX Systems I...aborIlories in the US.A. and other ccunaies.

02S-03C-007

(2)

2. Instaillngthe Maintenance Supplement

Use the following custom(ADM) procedure to install the maintenance supplemenc

1. Log onto your machine in system maintenance (single-user) mode and enter this command:

custom

You see the main custom menu.

2. Press (Remm) to select Install. A window opens in the lower right-hand corner.

3. Press (Remm) again to select A New Product. The next screen highlights Entire Product.

4. Press (Remm) to select Entire Product. The installation prompts you to insen Floppy Volume l.

s.

Insert the maintenance supplement and press (Return). The Product Prep Script determines whether the installation environment is correct.

If seQ TCP/IP is not installed, if you already have this maintenance supplement on your system, or if you are not in system maintenance mode, custom tenninates at this time.

If the installation environment is correct, custom backs up the files lusrlbinltelnet and letclconf/pack.dludplspace.c to the directory lusrllibluclpmslsave. The screen again prompts you for Volume 1.

6. Verify that Volume 1 is still in the drive, and press (Rerum). The message Ext:ac:tinq files ..•

appears and remains on the screen as long as custom is extracting .files from the disk.

Next, custom prompts you to relink the kernel.

7. ~"~~ Y to relink the kernel. unless you have other software to install. In that case, enter n and continue with step 8.

If you enter y, you see a series of messages that indicate the progress of the kernel relink and the resetting of the kernel environment.

8. Press any key to return to the custom menu.

9. When you are ready to exit custom, press q to quit. or use the left mow key to select Quit and press (Return).

10. Type shutdown and press (Return) to reboot the system.

3. Removing the Maintenance Supplement

Use the following custom procedure to remove all or part of the maintenance supplement:

1. Log into your system in single-user (system-maintenance) mode, type custom. and press (Rerum).

2. Usc the arrow keys to highlight Remove, and press (Return).

3. Highlight the seQ TCPIIP Maintenance Disk option, and press (Return).

4. Highlight the package that you want to remove, and press (Return). Press (Return) again to verify the package.

S. Re1ink the kernel when the system prompts you to do so.

6. Enter y when the system asks you if you want the kernel to boot by defaulL 7. Enter y when the system asks you if you want to rebuild the kernel environment.

8. When the system prompts you. press any key to return to the custom screen.

9. Select Qui4 then Yes to exit custom.

(3)

10. Type shutdown and press (Return) to reboot the system.

Sincerely yours, SeQ Product Marketing

Referenzen

ÄHNLICHE DOKUMENTE

Multiple program statements may appear on a single line, if separated by a (:) colon.. When the user types a left-arrow (under-line or RUBOUT on some

If a single protection domain is not established, then any user who does not have an account on a particular remote machine running TRFS can nonetheless access

These notes describe how to preserve and restore commonly customized system configuration files and directories so that the new system operates as expected.. Note that a

The software repairs in this release are described in the README file included on the tape. Create a directory, cd into it and extract the software from the

If no damage is apparent, open the shipping container and remove documentation, mounting hardware, and cables.. Check materials received in option

On read Record: In indicates the M5B of record-type code from data field address mark. On any Write Track: It indicates a Write Protect This bit is reset

Transmissions that are received with correct parity and valid type field are indicated by asserting ACK on the bus during the second time slot after the

The Cluster File Access Workstation Agent is installed on each client workstation that has disks to be accessed by other workstations in the cluster. On the Executive command